Knowledge Base:  
You are here: Knowledge Base > LYNX L5100

How do I program a Honeywell 5877 to my Lynx Touch alarm panel?


Last Updated: 12/05/2013
By

It's already programmed! But it's not that easy. In order to report the status of your garage door, you must program a transmitter, such as the 5822T tilt sensor or the 5816 door sensor.

Programming the 5822T to the Lynx Touch L5100 is pretty simple. To follow our instructions, click here.
The next step is to learn your 5877 wireless relay.

Follow the steps below:
1. On your 5100 keypad, go to "automation"
2. "Garage door setup:
3. "Garage door 1"
4. "Assign device"
5. Enter serial number. Then you're done there
7. Click the program button on the 5877
8. Return back to the 5100, select 'garage door 1/opener 1' and push the 'learn' button. The pairing is successful if you hear the relay click


The Honeywell 5877
makes it easy to add remote garage door control to your Honeywell wireless system. It allows for control of any relay-activated device with just the push of a button on a Honeywell 5800 series wireless security key fob, like the 5834.



Was this article helpful?

Comments:
 

Related Articles
 >

Can I use WIFI as a primary communicator on the LYNX L5100, and a GSM cellular communicator as a backup?


 >

Where is the best place to install the LYNX 5100?


 >

How do I make my L5100 panel compatible with Z-Wave?


 >

Does LYNX Touch 5100 use Z-Wave Motion Detectors?


 >

Why does it take the 5811 door sensor thirty seconds to set off an alarm on the L5100?


 >

What's the difference between a Rule and a Scene on the LYNX 5100?


 >

How do I hook up power to the L5100 Control Panel?


 >

What security cameras are compatible with the L5100 Touch?


 >

Can wired contacts be used with my LYNX Touch?


 >

Does the Honeywell LYNX L5100 have to be connected to a telephone line?


 >

Can the Lynx Touch L5100 work without Total Connect?


 >

How do I wire a Lynx Touch L5100 trigger?


 >

What deadbolt lock should I use with the LYNX Touch L5100?


 >

How does the Tuxedo Touch controller compare to the LYNX Touch L5100?


 >

How do I program a duress code on my Honeywell Lynx Touch L5100?


 >

Is the LYNX Touch compatible with any Vista Series Control Panel?


 >

How do I install the L5100 myself?


 >

Does the L5100 need to have an internet connection?


 >

How do I change the audio and visual display settings on my LYNX Touch L5100?


 >

What wireless routers will work with my L5100?


 >

Can you turn off an alarm siren on the L5100?


 >

How long is the Honeywell LT-Cable for the LYNX L5100?


 >

How does the LYNX Touch L5100 compare to the L5000?


 >

What can the GSMVLP5-4G do for the LYNX Touch L5100?


 >

How loud is a LYNX L5100 siren?


 >

How do I register the L5100 sim card with my GSMVLP5-4G Cellular Communicator?


 >

What happens if I lose internet connection on my L5100?


 >

Can the L5100 LYNX Touch support dual-path monitoring?


 >

How many zones does an L5100 have?


 >

How do I get the LYNX Touch L5100 to work with Total Connect?


 >

How do I change my L5100 installer code?


 >

How do I connect my smartphone or tablet to the LYNX Touch L5100?


 >

How do I enable chime mode on the L5100 control panel?


 >

How do I program the correct time and date into my L5100 Control Panel?


 >

How do I program a hardwired zone on my LYNX Touch L5100?


 >

Will the Honeywell 5818MNL work with the Honeywell Lynx Touch L5100?


 >

How can I access my Honeywell Lynx L5100 remotely?