Knowledge Base:  
You are here: Knowledge Base > LYNX L5100

How do I change my L5100 installer code?


Last Updated: 11/19/2013
By


If you know your installer code...
From the home screen of your L5100, click "More", then "Tools." Type your installer code (default: 4112) into the keypad display. In the programming menu, click "Program", then "Installer Code." Enter your new installer code here, then select "Done."


If you don't know your installer code...
And the default installer code (4112) didn't work, you need to power off the system. Then power the system back on. Press and hold the "Off" key while the "System Standby!" message appears on the display. When reboot stops, press the "Off" key again. Now a keypad will appear. Select "Clear", then enter "00" on the touchscreen display to arrive at the tools menu. From this menu, continue by following the steps above, as if you knew your installer code.


Similar Products:
LYNX Plus L3000
L5100-SIA


Was this article helpful?

Comments:
 

Related Articles
 >

Can I use WIFI as a primary communicator on the LYNX L5100, and a GSM cellular communicator as a backup?


 >

Where is the best place to install the LYNX 5100?


 >

How do I make my L5100 panel compatible with Z-Wave?


 >

Does LYNX Touch 5100 use Z-Wave Motion Detectors?


 >

Why does it take the 5811 door sensor thirty seconds to set off an alarm on the L5100?


 >

What's the difference between a Rule and a Scene on the LYNX 5100?


 >

How do I hook up power to the L5100 Control Panel?


 >

What security cameras are compatible with the L5100 Touch?


 >

Can wired contacts be used with my LYNX Touch?


 >

Does the Honeywell LYNX L5100 have to be connected to a telephone line?


 >

Can the Lynx Touch L5100 work without Total Connect?


 >

How do I wire a Lynx Touch L5100 trigger?


 >

What deadbolt lock should I use with the LYNX Touch L5100?


 >

How does the Tuxedo Touch controller compare to the LYNX Touch L5100?


 >

How do I program a duress code on my Honeywell Lynx Touch L5100?


 >

Is the LYNX Touch compatible with any Vista Series Control Panel?


 >

How do I install the L5100 myself?


 >

Does the L5100 need to have an internet connection?


 >

How do I change the audio and visual display settings on my LYNX Touch L5100?


 >

What wireless routers will work with my L5100?


 >

Can you turn off an alarm siren on the L5100?


 >

How long is the Honeywell LT-Cable for the LYNX L5100?


 >

How does the LYNX Touch L5100 compare to the L5000?


 >

What can the GSMVLP5-4G do for the LYNX Touch L5100?


 >

How loud is a LYNX L5100 siren?


 >

How do I register the L5100 sim card with my GSMVLP5-4G Cellular Communicator?


 >

What happens if I lose internet connection on my L5100?


 >

Can the L5100 LYNX Touch support dual-path monitoring?


 >

How many zones does an L5100 have?


 >

How do I get the LYNX Touch L5100 to work with Total Connect?


 >

How do I connect my smartphone or tablet to the LYNX Touch L5100?


 >

How do I enable chime mode on the L5100 control panel?


 >

How do I program the correct time and date into my L5100 Control Panel?


 >

How do I program a hardwired zone on my LYNX Touch L5100?


 >

Will the Honeywell 5818MNL work with the Honeywell Lynx Touch L5100?


 >

How can I access my Honeywell Lynx L5100 remotely?


 >

How do I program a Honeywell 5877 to my Lynx Touch alarm panel?