Skip to content
To take full advantage of this site, please enable your browser's JavaScript feature.
Learn how
516-812-0917
Shop Categories
Access Control
Fire & Life Safety
Burglar Alarms
Power Supplies
Batteries
Analog CCTV
IP Video Surveillance
Intercom
Wire & Cable
Tools & Supplies
Signal Transmission & Distribution
Wireless
My Account
Shop Brands
Login/My Account
Customer Service
Order Tracking
Return Policy
Knowledge Base
FAQ
Contact us
Contact us
Help
516-812-0917
Shop Our Categories
Search the store:
Search
Contact us
Help
516-812-0917
Shop Categories
Access Control
Fire & Life Safety
Burglar Alarms
Power Supplies
Batteries
Analog CCTV
IP Video Surveillance
Intercom
Wire & Cable
Tools & Supplies
Signal Transmission & Distribution
Wireless
My Account
Shop Brands
View All Brands
Login/My Account
Customer Service
Order Tracking
Return Policy
Knowledge Base
FAQ
Contact us
0
Knowledge Base
:
All
Questions By Product
Questions by Category
You are here:
Knowledge Base
>
Vista-20P Control Panel
Why is my Vista 20P displaying a "Check 100" message?
Last Updated: 12/04/2013
By
Petra Paulson
A "Check 100" message typically appears when a
wireless receiver
is disconnected or a hardwired zone is not programmed with the proper zone type.
For wireless receivers...
make sure the device is properly assigned to a zone on the
Vista 20P control panel
. For the
5881ENL
,
5881ENM
, and
5881ENH
wireless receivers, DIP switches must be set to address the device.
Click here for instructions on how to set the DIP switches on the receiver
.
For re-programming hardwired zones...
Access the zone programming menu from the home screen of your
alarm keypad
, then program the appropriate input type for the hardwired zone in question.
Similar Products
:
Honeywell 5883H Wireless Receiver
Vista 21iP Control Panel
Vista 15P Control Panel
Was this article helpful?
10 (Best)
9
8
7
6
5 (Average)
4
3
2
1 (Worst)
Comments:
Related Articles
>
Where Do I Find my VISTA 20P Panel Revision?
>
What Honeywell Glass Break Detectors Work with the Vista-20p?
>
How Do I Program a Vista-20P Duress Code?
>
How does the Vista 20P compare to the Vista 20PSIA?
>
Can I add sirens to the Vista 20P? And if so, how many?
>
How do I install the Honeywell GSMV4G and get it to work with my Vista 20P Control Panel?
>
How do I run a GO/NO GO test on my Vista 20P?
>
What are the device addresses for my Vista 20P?
>
Can I use Compass Software to program my Vista 20P Control Panel?
>
How many wireless transmitters will work with the Vista 20P?
>
How do I connect power to the Vista 20P?
>
How many keypads can I install with my Vista 20P?
>
How many events can be stored in the Vista 20P event log?
>
What is a security "event" on my Vista 20P?
>
How does a Tuxedo Touchscreen Keypad work with my Vista 20P?
>
How do I change the Partition 2 code for my Vista 20P?
>
How do I connect devices to the Vista 20P?
>
How do you connect a zone expander on the Vista 20P?
>
How do I program a Vista 20P Control Panel?
>
How many zones can the Vista 20P support?
>
How do I add a glass break sensor to the Vista 20P?
>
What revision chip do I need to make Vista 20P compatible with Total Connect 2.0?
>
How many wireless devices can the Honeywell 5881ENH wireless receiver support?
>
For how long does a VIsta 20P siren sound when it goes off?
>
What does "exit now" message mean when I arm my security system in "stay mode"?
>
What alarm systems are compatible with the wireless 5800Micra?
>
How do you arm a Honeywell security system?
>
When the alarm goes off on my Vista 20P control panel, will the system call my cell phone?
>
Why does an "E8" message appear on my Vista 15P or Vista 20P Control Panel?
>
Why won't the default installer code (4112800) let me access the programming menu on my Vista 20P Control Panel?
