Viking E-75-SS-EWP Video Entry Phone with Built-In Proximity Card Reader and Enhanced Weather Protection

The E-75 Series Video Entry phones are compact, weather and vandal resistant speaker phones designed to provide two-way handsfree audio communication and color composite video of who is at your door or gate. The E-75 also includes a built-in 125KHz proximity card reader that supports Viking PRX-C, PRX-C-ISO, PRX-FOB and certain legacy HID proximity protocols. The card reader outputs industry standard 26-bit Wiegand data, allowing it to be used with a Viking ES-1 door controller or any controller compatible with 26-bit Wiegand format.

The E-75's compact size allows it to be mounted in a standard double gang electrical box. The E-75 is available in five different attractive finishes to match your door hardware, light fixtures, etc. Replacement E-75 faceplates (PNL75) can be purchased separately and are available in all five standard finishes.

The E-75 entry phones can share a single phone line with house or small business telephones when used with a Viking model C-200, C-250 or C- 2000B Entry Phone controller. The E-75 entry phones can also be connected to an unused analog station port (programmed for ring down) on a phone system or connected directly to a telephone line when used with a Viking K-1900-5 or K-1900-30 dialer.

The E-75 features a built-in high resolution color video camera, a built-in proximity card reader, microphone and speaker volume controls, selectable auto answer for monitoring and intelligent call progress detection for automatic hang-up when the call is completed.

For outdoor installations where the unit is exposed to precipitation or condensation, the E-75 Series is available with Enhanced Weather Protection (EWP). For more information on EWP, see DOD# 859.

UPC: 615687224498
Also known as: E75SSEWP, VK-E75SSEWP

Technical Specifications: Operating Temperature: -34C to 65C (-30F to 150F) Humidity: Up to 100% LED: Red, turns off during card read Transducer: Beeps during card read Technologies Supported: Viking PRX-C, PRX-C-ISO, PRX-FOB and certain legacy HID proximity protocols* Read Range: 1.25 to 2.0 Format: 26 bit Wiegand Frequency: 125KHz Maximum Cable Length: 500 ft 24 Awg stranded shielded (Belden 9537) Power: 5 to 14V DC @ 60mA maximum Proximity Card Reader Specifications Recommended Surface Mount Box: Viking model VE-5x5 (DOD# 424) WARNING: Do NOT use a typical wet location box as not all styles seal properly with the E-75 faceplate. Recommended Electrical Box for Flush Mounting: Double gang with minimum inside dimensions of 2.25 deep x 3.65 wide x 2.84 tall (Carlon BH234R or equivalent) Shipping Weight: 0.55 kg (1.2 lbs) Connections: (5) gel-filled butt connectors (3M Scotchlok UR2) Humidity: up to 100% non-condensing Operating Temperature: -34 C to 65 C (-30 F to 150 F) Entry Phone / Camera Specifications Maximum Wire Run Length: 750 ft with RG59/RG6 for video and CAT5 for power (3 pairs) and entry phone audio (1 pair). 150 ft with CAT5E for video, power and entry phone audio (longer video runs are possible by using video balun transceivers). IR Compatibility: This camera is equipped with an OLP (Optical Low Pass) filter to maintain correct video color in outside applications. The standard camera is NOT compatible with IR illuminators. If IR illumination is required, you will need to replace the exisiting camera with a Viking model VCAM-1IR, see DOD# 190. Tilt/Swivel Adjustment: Vertical +/- 20, horizontal +/- 30 (see Diagram A) Lens: 3.4mm, pinhole 70 FOV (Field of View) Sensitivity: 0.26 LUX (20 IRE) F 2.0 Resolution: 420 lines (640 x 480 @ 30fps / 307,200 pixels) Video Output: 1 VP-P composite, NTSC, 75 ohms Image Sensor: 1/4 color CMOS Power: 3.5-6V DC regulated 150mA (5V DC regulated adapter included) Camera Specifications CPC Disconnect Time: 300ms minimum Ring Voltage: 25V AC RMS minimum (for auto answer) Speaker Volume: Approximately 62db maximum @ 1m Dimensions: Faceplate: 123.8mm x 125.4mm x 4.3mm (4.875 x 4.938 x 0.17), Phone: 72mm x 46mm x 42mm (2.84 x 1.8 x 1.65) Power: Telephone line powered. Minimum 18V DC talk battery voltage with a minimum loop current of 20mA. Loop current may be boosted on low current lines with a Viking model TBB-1B Talk Battery Booster (see DOD# 632). Entry Phone Specifications REN: 0.8A

For more information about the Viking Electronics E-75-SS-EWP, please contact us.