Takex PR-11BE Photoelectric Beam Sensor

  • MPN: PR-11BE
  • JMAC ID: 200013454
$188.00
In Stock
  • Expedited Shipping Available Expedited Shipping Available
  • Need it Tomorrow?
    Need it Tomorrow?
    Select the NEED IT FAST shipping option at checkout and a member of our team will contact you promptly with any available Expedited Shipping options once we receive your order.
JMAC_ID:
200013454
df_manual_boost:
2.20

The Takex PR-11BE is an indoor/outdoor reflective photoelectric beam sensor designed to detect interruptions across entrances, driveways, gateways, and security perimeters. Featuring a 36-foot (11 m) outdoor detection range, 49-foot (15 m) indoor range, and 10.5-30V DC power input, it combines a transmitter and receiver in one housing with a separate reflector. Single-side wiring, adjustable response time, and N.O./N.C. relay outputs simplify installation and integration with compatible security systems.

Takex PR-11BE Indoor/Outdoor Reflective Photoelectric Beam Sensor

The Takex PR-11BE reflective photoelectric beam sensor, also identified by distributor part number PU-PR11BE, provides infrared beam interruption detection for residential, commercial, and industrial security applications. Unlike conventional through-beam detectors that require electrical connections at both ends, the PR-11BE combines its infrared transmitter and receiver in a single sensor housing and uses a separate passive reflector. This configuration requires wiring on only one side of the protected area, reducing cable installation requirements. The sensor monitors distances of 3.3 to 36 feet (1 to 11 m) outdoors and 3.3 to 49 feet (1 to 15 m) indoors, supporting perimeter monitoring, driveway detection, gateway protection, and entrance monitoring.

The PR-11BE operates from a 10.5-30V DC non-polarized power supply with a maximum current consumption of 55 mA. Its reflective near-infrared detection system provides adjustable response time from 0.05 to 0.7 seconds, allowing installers to configure beam interruption sensitivity for the monitored area. The detector includes selectable normally open (N.O.) and normally closed (N.C.) dry-contact alarm outputs rated at 30V AC/DC and 0.5A maximum. A separate normally closed tamper contact activates when the sensor cover is removed. An ambient light compensation circuit and optical filtering help reduce interference from sunlight, vehicle headlights, and artificial lighting.

Installation and alignment are supported by 180-degree horizontal optical adjustment ( 90 degrees), 20-degree vertical adjustment ( 10 degrees), and an integrated alignment viewfinder. A monitor jack enables signal-level measurement with a compatible multimeter, while the red alarm and attenuation LEDs provide visual feedback during setup and testing. The sensor includes separate indoor and outdoor attenuation sheets for alignment procedures. Its IP54-rated housing supports indoor and outdoor installations, and the specified operating temperature range is -13 F to 140 F (-25 C to 60 C). Wall mounting is supported, with optional mounting accessories available for installations requiring pole attachment or adjustable brackets.

The Takex PR-11BE integrates with compatible intrusion alarm panels, monitoring equipment, and control systems through its dry-contact relay output. Applications include monitoring vehicle entrances, pedestrian gateways, access corridors, and other locations where installing wiring on both sides of a detection path is impractical. Optional accessories include the Takex BP-60A pole attachment, BL-11 reflector mounting bracket, and BL-1130 angle adjustment bracket. During installation, the sensor and reflector must be positioned with an unobstructed optical path, and response timing must be adjusted for the intended detection application. The PR-11BE is an intrusion detection device designed to initiate an alarm or control signal when its infrared beam is interrupted.



UPC: 100000901199
Also known as: PU-PR11BE, PR11BE

Technical Specifications:
  • Product Color: Wine Red
  • Form Factor: Pole-mountable, Wall Mountable
  • Material: Resin
  • Maximum Indoor Detection Range: 49 ft
  • Horizontal Adjustment: 90°
  • Product Material: Resin
  • Maximum Outdoor Detection Range: 36 ft
  • Vertical Adjustment: 10°
  • Maximum Response Time: 700 ms
  • Color: Wine Red
  • Maximum Response Time (Second): 0.7
  • Input Voltage: 30 V DC
  • Product Type: Photoelectric Beam Detector
  • Weight (Approximate): 15.17 oz


For more information about the Takex PR-11BE, please contact us.
  • Rotary Optical System
  • Double Modulated Beam for unsurpassed Light Immunity
  • Suitable for both Indoor and Outdoor use
  • Easy Installation
  • Easy Operation Check
  • Response Time Adjustment
  • Monitor jack for alignment with Multi-Meter

2 Reviews

  • 5
    TAKEX-PU-PR11BE

    Posted by 167309 on Feb 22nd 2021

  • 5
    TAKEX-PU-PR11BE

    Posted by 121278 on Dec 20th 2017

Live Chat