Inovonics EN4216MR 16 Zone Multi-Condition Receiver with Relay Outputs

  • MPN: EN4216MR
  • JMAC ID: 200017130
$335.00
In Stock
  • Expedited Shipping Available Expedited Shipping Available
  • Need it Tomorrow?
    Need it Tomorrow?
    Select the NEED IT FAST shipping option at checkout and a member of our team will contact you promptly with any available Expedited Shipping options once we receive your order.
JMAC_ID:
200017130
df_manual_boost:
2.05

The Inovonics EN4216MR is a 16-zone EchoStream wireless multi-condition receiver designed to integrate wireless security transmitters with hardwired alarm panels and standalone monitoring systems. Operating at 902-928 MHz using frequency hopping spread spectrum (FHSS) technology, the receiver supervises up to 16 single-condition or multiple-condition transmitters. Featuring six Form C relay outputs, a two-line LCD display, programmable relay operation, and tamper and RF interference detection, the EN4216MR provides wireless alarm monitoring and event reporting for commercial security installations.

Inovonics EN4216MR EchoStream 16-Zone Wireless Multi-Condition Receiver with Relay Outputs

The Inovonics EN4216MR 16-Zone Multi-Condition Receiver provides wireless alarm integration for commercial intrusion detection, security monitoring, and standalone alarm applications. Designed to communicate with up to 16 Inovonics EchoStream wireless transmitters, the receiver translates wireless alarm conditions into hardwired relay outputs for connection to compatible security control panels. Its 902-928 MHz frequency hopping spread spectrum (FHSS) technology provides wireless communication across the North American EchoStream frequency band. The receiver supports both single-condition transmitters and multiple-condition devices, including compatible panic buttons, universal transmitters, and security sensors. This configuration allows facilities to expand existing hardwired alarm systems without installing signal wiring between each wireless transmitter and the control panel.

The EN4216MR operates on 11-14 VDC with a 400 mA power requirement and provides six Form C relay outputs consisting of five alarm relays and one fault relay. Relay contacts are rated at 1A at 28 VDC or 0.5A at 30 VAC for resistive loads, supporting integration with compatible alarm panel inputs and monitoring circuits. Additional connections include a normally open case tamper output, normally closed RF jam indication output, and momentary reset input. The receiver weighs approximately 9.9 ounces (280 g) and operates within a temperature range of 32 F to 140 F (0 C to 60 C), with relative humidity up to 90% noncondensing. Its internal antennas eliminate the need for an external antenna assembly in standard installations.

The Inovonics EN4216MR includes a two-line text display and integrated programming controls for transmitter registration, signal strength evaluation, system configuration, and troubleshooting. The display identifies transmitter conditions, presents historical event information, and assists installers in verifying wireless communication during setup. Each relay output supports independently configurable follower, latching, momentary, or toggle operation, allowing the receiver to accommodate different alarm response requirements. Momentary output durations are programmable from 0.5 to 99.5 seconds. Built-in supervision monitors registered wireless devices for communication failures and trouble conditions, including low-battery indications, transmitter inactivity, receiver tampering, and RF interference. A dedicated fault relay allows these conditions to be communicated to a connected security panel.

The Inovonics EN4216MR EchoStream Receiver is designed for commercial security installations requiring wireless transmitter monitoring through conventional hardwired alarm inputs. Its 16-transmitter capacity, six relay outputs, programmable response modes, and onboard diagnostic display support applications such as intrusion detection, panic signaling, perimeter protection, and facility security monitoring. The receiver includes an integrated wireless enrollment routine and supports compatible Inovonics EN5040 Series high-power repeaters for installations requiring expanded wireless coverage. Manufacturer documentation identifies compliance with FCC, Industry Canada, RoHS, and applicable UL security standards, including UL 365, UL 636, UL 985, UL 1023, UL 1610, and UL 1076. Installers should verify transmitter compatibility, power supply capacity, relay assignments, receiver placement, and wireless signal strength before commissioning the system.



UPC: 875189004008
Also known as: IV-EN4216MR

Technical Specifications:
  • Frequency: 900 MHz
  • Dimensions: 6.35" x 3.5" x 1.0"
  • Relay Outputs: 5 Alarm/1 Fault
  • Transmitters: 16
  • Maximum Current: 400 mA
  • Power Requirements: 10 - 14 VDC


For more information about the Inovonics EN4216MR, please contact us.
  • Outputs can be configured in follower, latching, momentary, or toggle modes independently
  • Two line text display shows condition of each transmitter, provides log of past events, and displays signal strength
  • Includes support for both single and multiple condition transmitters
  • Add up to 16 high performance EchoStream wireless transmitters to any installation
  • Wireless programming routine built into the receiver
  • Case tamper protection, jam detection, and internal antennas for a secure wireless implementation
  • Six form C relays for connecting to any panel

2 Reviews

  • 5
    INOVONICS-EN4216MR

    Posted by 177760 on Nov 21st 2021

  • 5
    INOVONICS-EN4216MR

    Posted by 175673 on Sep 28th 2021

Live Chat