Honeywell PRO42R2B PRO4200 Dual Reader Access Module
-
MPN: PRO42R2B
-
JMAC ID: 202543771
The Honeywell PRO42R2B is a PRO4200 Series dual-reader access control interface module supporting two controlled doors, Wiegand and OSDP readers, eight supervised inputs, and six Form C relay outputs. Designed for integration with compatible Honeywell PRO42IC intelligent controllers, it communicates over an RS-485 bus at speeds up to 38.4 Kbps. The module operates on 12 VDC, features configurable reader power, monitored door and request-to-exit inputs, and onboard diagnostic LEDs. Its compact board supports rack or flat mounting in compatible PRO Series access control enclosures.
Honeywell PRO42R2B PRO4200 Dual Reader Access Control Module
The Honeywell PRO42R2B is a dual-reader access control interface module designed to expand compatible Honeywell PRO4200 security systems with support for up to two electronically controlled doors. Part of Honeywell's Professional Series access control hardware, the PRO42R2B connects to a compatible PRO42IC intelligent controller and provides dedicated interfaces for credential readers, door position switches, request-to-exit devices, electric locking hardware, and auxiliary monitoring equipment. The module supports Wiegand, Clock-and-Data, and OSDP reader communication, allowing integration with traditional proximity card readers and compatible modern smart credential technologies. Its modular design makes it suitable for commercial offices, educational facilities, healthcare properties, warehouses, and institutional buildings requiring expandable door security. Unlike a standalone door controller, the PRO42R2B operates as a downstream input/output module within a compatible access control system, with access permissions and system operation managed through the intelligent controller and supported security management software.
The PRO42R2B incorporates two reader interfaces, eight supervised general-purpose inputs, two dedicated unsupervised inputs, and six Form C relay outputs for access control and auxiliary equipment integration. The supervised inputs support door status switches, request-to-exit buttons, alarm contacts, and other compatible monitoring devices, with configurable circuit supervision using 1K-ohm end-of-line resistors. The dedicated inputs support enclosure tamper and power fault monitoring in applicable mounting configurations. Its six relay outputs include two door-control relays and four additional general-purpose relays, supporting electric locking interfaces, auxiliary signaling, and other approved equipment control functions. The module supports configurable relay activation and deactivation behavior, allowing authorized installers to implement normal or fail-safe switching logic according to the system design. Each reader interface supports compatible Wiegand or Clock-and-Data signals, while OSDP-capable connections provide an upgrade path for compatible bidirectional reader communication. The board also provides configurable reader LED and buzzer controls, enabling connected readers to display access status and deliver audible feedback during credential transactions.
The Honeywell PRO42R2B operates from a nominal 12 VDC Class 2 power source with a maximum specified current requirement of 650 mA when powering compatible readers. Its internal electronics require approximately 300 mA maximum, excluding reader loads, and reader power can be configured for compatible 5 VDC or 12 VDC devices using the board's selection jumpers. Communication with the PRO42IC intelligent controller is provided through a two-wire RS-485 interface supporting selectable transmission rates of 9,600, 19,200, or 38,400 bits per second. The manufacturer specifies a maximum RS-485 communication bus length of approximately 4,000 feet (1,200 meters) when properly installed using approved shielded twisted-pair wiring. Reader cable connections support distances of up to 500 feet (150 meters) under the manufacturer's specified wiring conditions, with additional limitations applying to OSDP wiring and termination. The module incorporates onboard diagnostic indicators for power, communication, reader activity, and input/output operation, helping technicians identify connection and configuration issues during installation and servicing. When communication with the host controller is interrupted, the module supports limited facility-code-based access operation when appropriately configured, with available functions determined by the intelligent controller and system programming.
The PRO42R2B features a compact circuit board measuring approximately 9 inches long, 5.5 inches wide, and 1 inch high (229 x 140 x 25 mm), allowing installation in compatible Honeywell PRO Series access control enclosures. It supports rack-mounted and flat-mounted configurations, with the available terminal connections and auxiliary input/output functions determined by the selected mounting arrangement. Compatible enclosure options include the PRO22ENC1 wall-mounted enclosure, PRO22ENC2 rack-mounted enclosure, and PRO22ENC3 enclosure configuration, subject to module capacity, power supply, and installation requirements. The board operates in indoor environments from 32 F to 120 F (0 C to 49 C) at noncondensing relative humidity levels within the manufacturer's specified limits. The PRO42R2B is designed for use with the Honeywell PRO42IC intelligent controller and compatible security management platforms, providing scalable reader and door control expansion for networked commercial access control systems. Compared with the PRO42R1 single-reader interface, the PRO42R2B accommodates two standard reader connections and additional supervised inputs and relay outputs. The related PRO42IN and PRO42OUT modules provide dedicated expansion for monitored inputs and relay-based equipment control. The PRO42R2B is supplied as an access control module rather than a complete enclosed controller assembly; required power supplies, batteries, readers, locking devices, and other integration components must be selected separately. Its combination of dual-reader connectivity, supervised door monitoring, relay-based locking control, RS-485 communication, and modular PRO4200 integration provides a flexible expansion solution for professional access control installations.
UPC: 085267591201
For more information about the Honeywell PRO42R2B, please contact us.