Bosch DS1101i Series Glassbreak Detector, Round Form 'C' Relay
-
MPN: DS1101I
-
JMAC ID: 200016352
The Bosch DS1101I is a round, hardwired acoustic glassbreak detector designed for residential and commercial intrusion alarm systems. Featuring microprocessor-based Sound Analysis Technology (SAT) and a maximum detection range of 25 ft (7.6 m), it detects the characteristic sounds of breaking plate, tempered, laminated, and wired glass. The detector operates on 6-15 VDC, draws 23 mA at 12 VDC, and includes a Form C alarm relay and normally closed tamper switch. Automatic environmental testing, sound-check functionality, and an alarm LED support installation and maintenance.
Bosch DS1101I 25 ft Round Acoustic Glassbreak Detector with Sound Analysis Technology
The Bosch DS1101I Acoustic Glassbreak Detector provides perimeter intrusion detection by monitoring the sounds associated with breaking framed glass in residential and commercial security installations. Part of the Bosch DS1100i Series, the detector uses microprocessor-based Sound Analysis Technology (SAT) to evaluate the frequency, acoustic signature, and timing characteristics of glass breakage before generating an alarm. It detects breakage involving plate, tempered, laminated, and wired glass, providing a maximum detection distance of 25 ft (7.6 m) for supported glass panels measuring at least 12 x 12 inches (30.5 x 30.5 cm). Its round, low-profile housing supports wall or ceiling installation near protected windows and glazed openings. The detector supplements door contacts and motion sensors by identifying glass breakage that may occur before an intruder enters the protected area.
The DS1101I operates on 6-15 VDC with a nominal supply voltage of 12 VDC and draws approximately 23 mA during normal operation or up to 29 mA in LED latch mode. Its integrated Form C reed relay provides normally open, common, and normally closed alarm contacts rated at 3.5 W and 125 mA at 28 VDC for resistive loads. A separate normally closed cover-activated tamper switch is rated at 125 mA at 28 VDC, allowing compatible alarm control panels to monitor unauthorized enclosure opening. The detector incorporates automatic environmental test circuitry to identify ambient noise conditions that could cause unwanted alarms, along with a magnet-activated test mode for use with the optional Bosch DS1110I Glassbreak Tester. An externally visible alarm LED indicates alarm and test conditions and supports optional latching operation. The automatic sound-check feature also permits a basic power and operation check through a handclap.
The Bosch DS1101I features a round, high-impact ABS plastic enclosure measuring 3.4 inches (8.6 cm) in diameter and 0.83 inches (2.1 cm) in depth. The detector mounts directly to a ceiling, an opposite wall, or an adjacent wall facing the protected glass. Bosch recommends positioning the detector 10-20 ft (3-6 m) from the glass and within 30 degrees of the glass centerline, while maintaining the maximum 25 ft distance to the farthest protected corner. The detector should not be installed on the same wall as the protected window or within 5 ft (1.5 m) of the window wall or a hard, sound-reflecting surface. Installation guidance also specifies at least 2 ft (0.6 m) of separation from heating and cooling outlets. Its specified operating temperature range is -20 F to 120 F (-29 C to 49 C), restricted to 32 F to 120 F (0 C to 49 C) for UL-certificated installations. Actual detection coverage depends on glass construction, room acoustics, furnishings, and mounting location.
The DS1101I glassbreak detector supports intrusion protection for offices, retail stores, educational facilities, residential properties, and commercial buildings with vulnerable glass windows or partitions. Its 25 ft acoustic detection range, environmental noise testing, and conventional Form C relay output allow integration with compatible hardwired intrusion alarm control panels. The detector is UL 639 Listed and ULC-S306 certified for applicable intrusion detection applications, with additional CE conformity documented by Bosch. The related Bosch DS1102I provides comparable acoustic detection in a square housing, while the DS1103I uses a flush-mount design for installations requiring a recessed appearance. Bosch identifies the DS1110I Glassbreak Tester as the compatible accessory for verifying detector placement and acoustic response. The DS1101I is intended as one component of a perimeter security system and does not replace motion detection or other intrusion sensors. Bosch specifies a 3-year manufacturer warranty for the detector family. Installers must verify protected glass types, environmental conditions, control panel wiring, and detector response before placing the system into service.
UPC: 782695261149
Also known as: DS-DS1101I, BOS-DS1101I
Technical Specifications:
|
For more information about the Bosch Security DS1101I, please contact us.
- Microprocessor-based sound analysis technology (SAT)
- Automatic environmental test circuitry
- Sound check
2 Reviews
-
BOSCH-DS1101I
-
BOSCH-DS1101I