Alarm Controls TS-2T Electronic Timer Request to Exit Station Square Pushbutton, 2 Amp At 35 Volt DC, 2 - 45 Sec Adjustable Timer Delay, SPDT, Green

The Alarm Controls TS-2T is a single-gang request-to-exit station with a 2-inch green illuminated PUSH TO EXIT button, adjustable 2-45-second electronic timer, and SPDT relay contacts rated at 2 amps at 35 VDC. Designed for commercial electronic access control systems, it operates from 12-24 VAC/VDC and provides a timed release signal for compatible electric locks and door controllers. The station features a 430 stainless steel wall plate, high-brightness LED illumination, and 2-1/2-inch mounting depth. Its timer automatically restarts when the button is pressed again, and the device is UL 294 listed.

Alarm Controls TS-2T Illuminated Request-to-Exit Push Button with Adjustable Timer

The Alarm Controls TS-2T is a single-gang request-to-exit (REX) push button station with an integrated electronic release timer, designed for commercial access control and electrically secured door applications. Manufactured by Alarm Controls, an ASSA ABLOY Group brand, the TS-2T provides a manual means of initiating an authorized door release through a compatible access control panel or electric locking circuit. The station features a 2-inch green square illuminated push button prominently labeled PUSH TO EXIT, making the activation point easy to identify at controlled entrances and exits. Its brushed 430 stainless steel wall plate provides a durable mounting surface suitable for offices, educational facilities, healthcare buildings, commercial properties, and institutional environments. Unlike basic momentary request-to-exit buttons, the TS-2T incorporates an adjustable electronic timer that maintains its relay output for a predetermined interval after activation, allowing occupants sufficient time to pass through a properly configured controlled doorway.

The TS-2T incorporates a momentary-action push button connected to a single-pole double-throw (SPDT) timed relay output. When the button is pressed, the electronic timer activates and changes the relay contact state for the configured release period. The timer is field-adjustable from 2 to 45 seconds, allowing installers to coordinate the release duration with the door hardware, access control sequence, and building requirements. A built-in adjustment potentiometer controls the delay, with clockwise rotation increasing the interval toward 45 seconds and counterclockwise rotation reducing it toward 2 seconds. If the push button is pressed again before the current timer interval expires, the timer restarts its countdown, extending the active release signal without requiring the user to continuously hold the button. Once the programmed interval expires, the relay returns to its normal contact state, allowing the connected locking equipment to resume its configured secured condition. This resettable timing function is useful for doors requiring a temporary release period rather than continuous unlocking.

The Alarm Controls TS-2T operates from a 12-24 VAC or VDC low-voltage power source, supporting integration with commonly used access control power supplies and door control systems. The manufacturer specifies SPDT timed relay contacts rated at 2 amps at 35 VDC, with common (COM), normally open (NO), and normally closed (NC) connections for compatible control circuits. These contacts allow the station to interface with an access controller's request-to-exit input or appropriately rated electric locking circuit. The installation instructions identify a maximum timer supply current of 60 mA, while the illuminated push button uses a separate LED connection that supports 12 or 24 VAC/VDC operation. At 12 VDC, the button LED draws approximately 7 mA, increasing to approximately 18 mA at 24 VDC. The timer, relay, and LED connections are identified through dedicated terminals on the electronic assembly, simplifying installation and troubleshooting. Because the relay provides switching contacts rather than a dedicated power supply output, connected electric locks require a suitable external power source and proper electrical protection.

The TS-2T features a 2-inch square green illuminated actuator mounted on a single-gang 430 stainless steel wall plate. The manufacturer specifies a switch assembly depth of 2-1/2 inches behind the mounting plate, which must be considered when selecting an electrical box or preparing the installation location. The timer installation instructions call for vertical wall-plate mounting in a compatible electrical box and provide terminal assignments for the operating power, SPDT relay, and push button illumination. The high-brightness LED improves visibility of the exit button in interior locations where occupants need to identify the manual release control. The stainless steel mounting plate provides mechanical durability and a professional appearance for high-traffic commercial entrances. The standard TS-2T includes one timed SPDT contact set, while related Alarm Controls configurations provide additional switching arrangements. The TS-2TD offers dual-pole double-throw (DPDT) timed output, and the TS-2-2T provides separate momentary and timed SPDT outputs. Other available configurations include red buttons, PUSH TO ENTER legends, blank buttons, and replacement LED components.

The Alarm Controls TS-2T is designed for request-to-exit signaling, timed electric lock release, and compatible access-controlled door applications. Its adjustable electronic timer allows installers to provide a controlled release interval for electromagnetic locks, electric strikes, and other appropriately rated locking equipment when incorporated into a compliant door control system. The device is UL 294 listed for access control system applications under UL File Number SA32686. The illuminated push button and built-in timer provide a convenient means of initiating normal authorized egress, while the connected access control system determines the final locking and release sequence. For doors subject to special access-controlled egress or electromagnetic locking requirements, the TS-2T must be installed with all independently required emergency release equipment, fire alarm interfaces, and mechanical egress provisions. It should not be treated as the sole emergency release method where applicable building and life safety codes require additional protection. Unlike an ordinary momentary switch, the TS-2T combines illuminated manual activation with a resettable 2-45-second electronic release timer in a compact single-gang assembly. Its durable stainless steel construction, configurable contact interface, and UL 294 listing make it suitable for commercial access control installations and compatible door security retrofits.