|
|
|
|
Linear EXA-1000 Omni-Directional Remote Antenna Also known as: EXA1000, LN-AAE00198 The Model EXA-1000 Omni-directional Remote Antenna is designed to enhance the radio range of Linears receivers. This antenna can be connected to the F connector on many Linear receivers to improve their range when they must be located in poor signal reception locations. Usually an increase of 20-30% range can be expected. The versatile EXA-1000 can be mounted in a variety of ways. A 2-inch U-bolt is supplied for post or pipe mounting, or the U-bolt holes in the Base Plate can be used to screw the antenna to a wall or vertical wood brace or beam.
NOTE: Generally, the higher the antenna is mounted above ground level, the better the radio range will be.
The EXA-1000 is a 1/2 wave, center fed, vertical antenna composed of three parts: an Antenna assembly with an F connector attachment; a Base Plate assembly with radial mounting provisions; and a five-foot, 75-ohm coaxial cable. The cable connects to the antenna base on one end and the receivers F connector on the other. If the antenna must be mounted further than five feet from the receiver, an extension cable of up to a maximum of 25 feet may be used instead of the five foot cable supplied. Because of the cable resistance, the performance of the EXA-1000 may be degraded by using longer than a 25 foot cable. |
Features:
- Compatible with all Linear receivers with Type F antenna connector
- Receives signals in 288 to 320 MHz range
- Omni-directional remote antenna
- Includes 5 feet of coax
- U-bolt for post mounting
|
Technical Specifications:
- Operating Frequency: 315 MHz
- Data Format: DX format
- Number of Codes: 1,048,575
- Number of Channels: DXR-701, one channel, DXR-702, two channels
- Measure Range: 700 feet in one quadrant with DXT-21 transmitter; 500 feet in open air (four quadrant test)
- Operating Temperature: 32 to 140 F (0 to 60 C)
- Sensitivity: -95 dBm (typical)
- Number of Stored Transmitter Codes: 32 per receiver
- Receiver Output: For "C" relay contact, 1 amp, at 32 VDC per channel
- Field Selectable Receiver Output Modes: Momentary, four seconds (factory set), Momentary, one second, Flip-flop toggle latch, 2-Channel
- Mode Button (one per channel):
- Learn Mode: Press and release to enter learn mode
- Transmitters Learned: Press and hold for five seconds after the last LED flash to delete all transmitters on an associated channel
- Erase Memory: Press and hold for five seconds after the last LED flash to delete all transmitters on an associated channel
- Clear Latch: Press and release
- Clear Low Battery: Press and release mode switch on channel 2 (DXR-702 only) to clear low battery
- LED Indicator Steady: Indicates "learn" mode; Flashing: Indicates number of transmitters learned on the selected channel; RF Activity: Blinks synchronously with detected RF activity
- Antenna DXR-701: Wire lead; DXR-702: F-connector with antenna (supplied)
- Input Impedance: 75 Ohm - 2:1 VSWR
- Operating Voltage: 11 to 17.5 VDC 12 to 16 VAC
- Current: 25 mA at standby at 12 VDC; 60 mA in alarm at 12 VDC, DXR-701; 90 mA in alarm at 12 VDC, DXR-702
- Connectors: Screw terminal,+,-, with N/O, N/C, and common per receiver channel
- Accessories: Mounting bracket, screws, and anchors (supplied)
- Regulatory Requirements: FCC and DOC
- Dimensions: 3 W x 19.5 H x 6 D
|
UPC: 93863110870
Average rating: 5.0, based on
2 reviews
For more information about the Linear EXA-1000, please contact us.
|
|
|
|
|
|
|