Securitron Exit Bars | JMAC Supply

UL/cULALVY.BP7041

CSFM 3774-0923:0103

ANSI/UL 294 Listed

Underwriter's Laboratories: File BP7041 (UL 294)

Product Features

The XMS is an exit motion sensor, which is versatile for hands-free exit requests. When approaching the motion sensor, it will reliably detect motion nearby and release the magnetic lock on the door. It's explicitly designed to release that lock from the inside for free egress. The XMS is fail safe, so if power is cut to the detector, the magnetic lock will safely release. A relay is present to send a REX (request to exit) signal to an access control system and shunt an alarm report. Control of the exit detection pattern, which is easily adjustable will allow for maximum security from the outside and avoidance of activation from the inside when not desired. Note that it is recommended to have an emergency exit button to be used in conjunction with the XMS to meet applicable building codes. It’s UL listed and comes with the MagnaCare lifetime replacement, no fault warranty.

Specification Data

This is for indoor use only weighing at 0.5 lbs. It has an input voltage of 12 or 24VDC and a power draw of 20-50mA depending on switching status.

Models

There is only the one model, the XMS (Exit Motion Sensor)

EEB

UL/cULALVY.BP7041 /UEHX7.BP7041

CSFM 3774-0923:0104

ANSI/UL 294 Listed

No.205 Listed

CSFM – California State Fire Marshal

California State Fire Marshal: 3774-0923:104

U.S. Patents:EEB2 & EEB3N - Underwriter's Laboratories: File BP7041 (UL 294)

Product Features

EEB is the emergency exit button, which is a backup to ensure safe egress. The exit device is installed next to the door to provide additional safety as required by code when using a motion detector. When pressing the button, it will release the door for 30 seconds. If pressed again during the 30-second lock release period, the unit will “retrigger” which will start a new 30-second lock release period. This is intended only for the release of a magnetic lock from the inside of a door. It operates on 12 or 24 VDC and includes switchable green, red and blue lenses. Note the red and white wires from the EEB2/3N must receive the voltage from the same power supply.

Models

There are several models of the EEB; there is the EEB2 (EEB w/30 Sec. Timer – SG, Green/Red/Handicap), then there is the EEB3N (EEB w/ 30 Sec. Timer – Narrow Stile, Green/Red). Then there are the illumination kit models, with the PB2-LK (Illumination Kit for PB2E, PB5E, EEB2 Series Push Buttons), and lastly the PB3-LK (Illumination Kit, Green/Red for PB3E/EEB3N Series).

PB Series

Product Features

High-quality push buttons are available in a wide selection of colors, sizes, switch types and outputs. They can release any maglock, alone or with door closers and other hardware. The model PB is a spring loaded exit button with multi-color illumination, mounted on a stainless steel single gang outlet box cover. It is also waterproof NEMA 4 rated which makes it safe for the outdoors, and for the push buttons that are not waterproof, there is always the WCC and WBB available for all single gang push buttons, key switches, and keypads. The PB comes with switchable green and red buttons, a Red LED on the plate, and 7 Amp rated contacts.

Models

There are only two models with the PB series, one is their standard issue of PB (Momentary, SG, DPST, and Illuminated w/ Red/Green Lens) and PBA which is the same thing, except instead of momentary, it’s alternate.

PB2 Series

PB2 Installation Instructions

PB22 Installation Instructions

PB2-LK Installation Instructions

PB2E Installation Instructions

PB3 Installation Instructions

Product Features

The model PB2 is a spring loaded momentary exit button, which is mounted on a stainless steel box cover. Included are switchable lenses that come in green, red and blue. While the PB series had a medium round button, the PB2 comes with a large square with easy to read text. It comes with different options, to be illuminated, single or double pole, and a red LED on the plate. The most common applications for this exit device are release of a fail-safe or secure electric lock. The other most common use is a timed release of a fail-safe electric lock using the PB2’s TimeMate. To make this weatherproof, the WCC and WBB are available for all push buttons, key switches, and keypads.

Models

There are several models with the PB2 series, their standard issue is just the PB2 (PB – Momentary, Single Gang, Illuminated, Green/Red/Handicap), the PB22 (PB – 2”, Sq Green Mom, DP w/Light – SG, Green/Red/Handicap), next is the PB2E (PB – Momentary, Single Gang, Green/Red/Handicap) and lastly the PB2-LK (Illumination Kit for PB2E, PB5E, EEB2 Series Push Buttons).

PB3 Series Catalog Page

PB3E Installation Instructions

PB3-LK Installation Instructions Architectural Specifications

Product Features

The model PB3 is a spring loaded momentary exit button, which is mounted on a stainless steel box cover. It has bi-color illumination. The red and green lamps can be individually operated according to the installation needs. The red lamp is an LED that is mounted above the button, and the green lamp is an LED which illuminates the button itself. It also has the ability to change from DPST to DPDT when it comes to the field. If you wish for it to be weatherproof, there is the WCC and WBB options for the buttons, key switches, and keypads. At a size of 4.5” x 2.75” (114mm x 70mm) or 4.5” x 1.75” (114mm x 44mm) depending on the plate, this device can fit in the smallest of places for your convenience.

Models

There are many different models for the PB3, such as its standard model, the PB3 (PB – Momentary, Single Gang, Illuminated, Green/Red Lens), then there is the PB3A (PB – Alternate, Single Gang, Green/Red Lens), the PB3AN (PB – Alternate, Narrow, Green/Red Lens). Other models are the PB3E (PB – Momentary, Single Gang, Green/Red Lens), the PB3EA (PB – Alternate, Single Gang, Green/Red Lens) and the BP3AN (PB- Alternate Narrow, Green/Red Lens).

Then we have BP3EAR (PB – Remote Alternate, Surface Mount Green/Red Lens) and the PB3EN (PB – Momentary, Narrow Green/Red Lens) and the PB3ER (PB – Remote Momentary, Surface Mount Green/Red Lens). Finally, the last two models are the PB3-LK (Illumination Kit, Green/Red for PB3E/EEB3N Series) and the PB3N (PB – Momentary Narrow, Green/Red Lens).

PB4L Series

Product Features

The key feature of the PB4L series is that it is an all steel unit specially designed to resist vandalism. It cannot be removed or tampered with from the outside and designed to resist shocks such as hammer blows. Otherwise, this illuminated exit button can be used for quick release of fail-safe or secure electric locks. The illumination comes in a bi-color LED of red or green.

Models

There are four different models, the PB4L-2 (PB (DP), Momentary, Single Gang, and Green Illuminated Halo) then the other single gang model is the PB4LA-2 (PB (DP), Alternate, Single Gang, and Green Illuminated Halo). The two narrow stile models are the PB4LAN-2 (PB (DP), Alternate, Narrow Stile, and Green Illuminated Halo) and lastly the PB4LN-2 (PB (DP), Momentary, Narrow Stile, and Green Illuminated Halo).

PB5 Series

PB5 Installation Instructions

PB5E Installation Instructions

PB2-LK Installation Instructions

Product Features

The model PB5 is a spring loaded momentary 2” diameter, exit button. This button is mounted on a stainless steel single gang outlet box cover that is 4.5” x 2.75” (114mm x 70mm). It can be used for momentary release of fail-safe or secure electric locks. It comes with a retro-fit wall mounting device and color-coded hookup wires installed. There are different versions of the PB5, such as the PB5E which is an economy version, which is supplied without a retro-fit wall mounting device and without hookup wire. More varieties are shown in the models section. This exit device is also convertible from DPST to DPDT.

Models

There are three different models, the standard model PB5 (PB-2” Round, Momentary, DPST, w/Light, SG, Red/Green/Handicap), and the PB5E, which is the economic version (PB-2” Round, Momentary, DPST, w/o Light, SG, Red/Green/Handicap) and lastly the PB2-LK (Illumination Kit for PB2E, PB5E, EEB2 Series Push Buttons).

DSB

Dual Sense Bar Brochure

CAN/ULC-S533 Listed

ANSI/UL 294 Listed

CSA-C22.2 No.205 Listed

NFPA 101

Patent pending

Product Features

The DSB is a dependable dual sense bar. It is the most reliable exit device available for magnetically locked doors. This exit device can be installed on all types of interior metal, aluminum or wood doors. It has a unique design which delivers superior fault tolerance with two independent, redundant switch circuits for releasing the lock. What makes this device unique is its ability to be used in multiple ways, such as being released by a mechanical movement trigger, or it can be released by a reliable touch sense technology. This way it simplifies use and ease of exit for personnel with prosthetics or those with occupied hands. It is resistant to interference from radio frequencies or electromagnetic frequency and external impact attempts.

Specification Data

Its shipping weight is 6lbs (2.72kg) to 8lbs (3.63kg) depending on the length. However, it can be field cut to fit non-standard door widths. The dual sense bar has an electrical of 24 mA at 12VDC or 24VDC, while the DSB with illumination can be 44mA at 12VDC to 24VDC. It has an operating temperature of +32 to +120F (0 to +49C) and for indoor use only.

Models

The DSB comes in many different models and different sizes. There are the black anodized models such as DSB-BK (36”), the DSB-BK42 (42”) and the DSB-BK48 (48”). Then there are the black anodized, illuminated models like the BSK-BKI (36”), the DSB-BKI42 (42”) and the DSB-BKI48 (48”). Next are the clear anodized models with DSB-CL (36”), the DSB-CL42 (42”) and the DSB-CL48 (48”). There is an illuminated version of the clear anodized with the DSB-CLI (36”), the DSB-CLI42 (42”) and the DSB-CLI48 (48”). The next sets of models are the dual sense bars with electrolynx. There is the EL-DSB-CL (36”), the EL-DSB-CL42 (42”) and the EL-DSB-CL48 (48”). Lastly the TC P-BK (Touch Bar Cover Plates – Set of 2, Black Anodized) and the TC P-CL (Touch Bar Cover Plates – Set of 2, Clear Anodized) finish the long list of models.

TSB

Installation Instructions Templates

UL/cUL FWAX2.SA6635 UL/cUL ALVY.BP7041 /UEHX7.BP7041

CSFM 3774-0923:0102

CSFM

3774-0923:0103 ANSI/UL 294 Listed

CSA-C22.2 No.205 Listed

CSFM – California State Fire Marshal Approved

MEA- City of New York Approved

CE: EN 50091-1,EN 61000-6-2 Approved

Product Features

The TSB is a Touch Sense Bar which provides touch-triggered release of magnetically locked doors. Touching the bar, even through light gloves or clothing, triggers an electronic sensor that will release the lock. This exit device is for indoor use only and is installed easily on all types of metal, aluminum or wood frame doors. The assembly consists of an aluminum bar available in lengths that will fit a standard U.S door. The bar varies from 36, 42 and 48 inches. For safety purposes, in an unlikely event of sensor failure, a push switch is mounted on the back side of the bar. It comes with a 16 ft. (4.8m) 22AWG 6 conductor cable and armored door cord included and operates on 12 or 24VDC. It comes with the MagnaCare lifetime replacement, no fault warranty.

Specification Data

Its shipping weight is 7lbs to 9lbs depending on the length. However, it can be field cut to fit non-standard door widths. The dual sense bar has an electrical of 12VDC or 24VDC and has a current draw of 40mA at rest; 25mA releasing. It has an operating temperature of +32 to +110F (0 to +43C) and for indoor use only.

Models

The TSB comes in many different models and different sizes. There are the black anodized models such as TSB-BK (36”), the TSB-BK-42 (42”) and the TSB-BK-48 (48”). There is the TSB-BKT which is the 36” model with a trailing edge timer (3 sec). Next are the clear anodized models with TSB-CL (36”), the TSB-CL-42 (42”) and the TSB-CL-48 (48”). The TSB-CLT is the 36” model with trailing edge time (3 sec) and a 42” TSB-CLT-42 model. The next sets of models are the weather-resistant bars. There is the DTSB-BK (36”), the DTSB-BK-42 (42”) and the DTSB-BK-48 (48”). Then we have the clear anodized weather-resistant models with the DTSB-CL (36”), the DTSB-CL-42 (42”) and the DTSB-CL-48 (48”).

Then we have the black anodized models with electrolynx with the EL-TSB-Bk (36”), the EL-TSB-BK-42 (42”) and the EL-TSB-BK-48 (48”). The clear anodized models are EL-TSB-CL (36”), the EL-TSB-CL-42 (42”) and the EL-TSB-CL-48 (48”). There is the TCP-BK (Touch Bar Cover Plates, Black Anodized) and the TCP-CL (Clear Anodized Touch Bar Cover Plates). Finally, there is the TSB-TDM (Through Door Mounting Kit for TSB).

EMB

Sell Sheet

ANSI/UL 294 Listed

Product Features

The EMB, which is an electromechanical exit bar, is used on magnetically locked, non-fire-rated doors or as an initiate device for a delayed egress timer. Pressing the bar would activate an internal mechanical switch that would release the lock. There are optional waterproof switches. Note, to order any electromechanical bar listed with waterproof switches; you just add the letter "W" to the front of the part number. However, the all-metal construction of the bar stands up to the harshest environments.

Specification Data

Its shipping weight is 7lbs to 9lbs depending on the length and has an operating temperature of -4 to +185F (-20 to +85C).

Models

The EMB comes in many different models and different sizes. There are the black anodized models such as EMB-BK (36”), the EMB-BK-42 (42”) and the EMB-BK-48 (48”). Next are the clear anodized models with EMB-CL (36”), the EMB-CL-42 (42”) and the EMB-CL-48 (48”). The next sets of models are the black anodized weather-resistant bars. There is the WEMB-BK (36”), the WEMB-BK-42 (42”) and the WEMB-BK-48 (48”). Then we have the clear anodized weather-resistant models with the WEMB-CL (36”), the WEMB-CL-42 (42”) and the WEMB-CL-48 (48”). Lastly, there is the TCP-BK (Touch Bar Cover Plates, Black Anodized) and the TCP-CL (Clear Anodized Touch Bar Cover Plates). Finally, there is the TSB-TDM (Through Door Mounting Kit for TSB).

TSH

Template

UL/cUL ALVY.BP7041 /UEHX7.BP7041

UL Certificate of Compliance (CoC)
CSFM 3774-0923:0102

CSFM 3774-0923:0103

ANSI/UL 294 Listed

CSA-C22.2 No.205 Listed

CSFM – California State Fire Marshal Approved

MEA- City of New York Approved

CE: EN 50091-1, EN 61000-6-2 Approved

Product Features

The TSH, or the touch sense handle, is an exit device for doors secured by electric locks. Sized to conceal existing mounting holes, it makes its installation aesthetically pleasing. It replaces standard pulls on aluminum doors to allow maglock release for egress. This exit device can be used on in-swing doors or even push-open devices for out-swing doors. The assembly consists of a plastic base with an electronic touch sensor mounted inside, and an aluminum handle which is used to pull or push the door open. When one touches the handle, a DPST 2 Amp rated relay is activated, and it trips the relay in the sensor, releasing the lock. In the unlikely event of sensor failure, a push switch is mounted on the plastic base. This device is electrolynx ready and comes with a 16ft (4.8m) 22AWG 6 conductor cable and armored door cord as well as the MagnaCare lifetime replacement, no fault warranty.

Specification Data

Its shipping weight is 3lbs with an operating temperature of +32 to +110F (0 to +43C). The Voltage is 12 or 12VDC with a current draw of 40mA at rest and 25mA releasing.

Models

The TSH comes in only 4 different models. The first two are just the standard push/pull models, with the TSH-BK (Black Anodized) and the TSH-CL (Clear Anodized). The other two have electrolynx incorporated along with them with the EL-TSH-BK (Black Anodized) and the EL-TSH-CL (Clear Anodized).

EMH

Product Features

The EMH electromechanical handle, works on any push, pull or swing-through door, and is designed for specialized outdoor applications. Mounting holes for this model are not pre-drilled at the factory and must be drilled by the installer. Once done, push the 8 pin plug protruding from the wire-way hole back into the door so that the connector does not interfere when marking the mounting holes. This exit device includes a 6 conductor cable assembly with a 6 pin IDC connector at one end and an 8 pin receptacle at the other.

Models

The TSH comes in only 4 different models. The first two are just the standard models of the electromechanical handle but in different colors, the first is the EMH-BK (Black Anodized), and the other is the EMH-CL (Clear Anodized). The third model includes the electrolynx and is only available in the EL-EMH-CL model (Clear, ElectroLynx) and the EL-EMH-BK (Black, ElectroLynx).

SP-1

Product Features

The SP-1 is a touch sensitive wall switch which is generally used as a superior alternative to wall mounted mechanical push buttons. It uses touch sensing technology to create a push plate with no moving parts. Intended for indoor use only, the unit is oversized to cover a single gang cutout. This device operates a set of internal dry contacts when touched by the human hand (even through gloves). It also includes an internal timer (0-25 seconds), a red LED which indicates operation and a redundant backup switch. A three-part vinyl decal is included alongside the MagnaCare lifetime replacement, no fault warranty.

Specification Data

At a shipping weight of 1.5 lbs., this device has an operating temperature of +32 to +110F (0 to +43C). It has a voltage of 12 or 24VDC and a current draw of 40mA at rest and 25mA releasing.

Models

The TSH comes in only 3 different models. The first is the standard touch sensor plate SP-1. The others involve pieces that work with the SP-1, such as the SP-1L (Label Touch Plate) and the SP-1LH (Label Touch Plate – Handicap Decal).

WSS