You are here: Home > Securitron > Electromechanical Locks
We found 44 results matching your criteria.
Sort By:
1 2 3
   
 
1 2 3

Electromechanical Locks & Accessories

With the best in mechanical and electrical engineering, Securitron offers electromechanical products and accessories to assist you with your latest project's needs. There are many different options we are going to explore, such as:

  • GL1
  • FMK
  • MM15 (Below are different Accessories for the MM15)
  • DC – MM15
  • HEB – MM15
  • SFP – MM15
  • TS – MM15
  • Z – MM15
  • UNL
  • MUNL
  • FSUNL

GL1

Installation Instructions
Gate & Fence Brochure Catalog Page Sell Sheet

Patent: 8,047,582

Product Features

In 2015 this electromagnetic lock did not just come with 2000 pounds of holding force, it came with a gold Govie, which is the government security award for locks, doors, and hardware. Where weather-resistant access control and security are required, the GL1 is designed to secure a variety of vehicles and pedestrian gate. It provides these functions in both electrically and manually operated gate installations and can be used for swinging or sliding for a vehicle, pedestrian or stock cage gate access controls or other applications. At a size of 2-3/4"L x 7-14"W x 3-1/4" D, it'll fit your needs.

This model is used for swinging or sliding for vehicle, pedestrian or stock cage gate access controls. It has automatic dual voltage, with no field adjustment required. It has a self-aligning receiver (+/- ½” horizontally) that helps compensate for the gates misalignment and sag. It also accepts a standard mortise cylinder with Adams Rite MS cam for the manual key override. To top it off, its tamper-resistant cast housing, optional latch status monitor and surface mount, and it comes with the MagnaCare lifetime replacement with no-fault warranty.

Specification Data

These products dimensions are 2-3/4"L x 7-14"W x 3-1/4" D, with two different varieties of electrical choices. The 12 Volts initial peak (~1.0 sec.) @ 870mA - Reduced: 290mA power consumption: 3.5 Watts, while it’s 24 Volts initial peak are (~1.0 sec.) @ 720mA - Reduced: 170mA power consumption: 4.1 Watts. It’s for indoor or outdoor use, and its operating temperature can go from -58 to +168F [-50 to +75C]. It weighs are 6lbs [2.72kg] and comes with a black finish.

Models

These come in several different models; each one has a 12/24VDC. The difference is the standard and monitored. The GL1-FL (Standard Fail Locked) and the GL1-FS (Standard Fail Safe) are the standard issues. The monitored are the GL1-FLM (Fail Locked Monitored) and the GL1-FSM (Fail Safe Monitored). Lastly, the GMC (Gate Lock Mortise Cylinder) is used for FL models only.

FMK

Installation Instructions Gate & Fence Brochure Flex Mount Bracket Kits Catalog Page

Product Features

FMK stands for flex-mount gate lock bracket kits. This bracket is used exclusively with the 1200 lb. holding force M62FG-SASM gate magnalock, as well as the 2000 lb. holding force GL1 gate lock. It will function with the GL1 when post separation is between 1” and 3-3/4”. The FMK-SL will function without SASM when the post-separation is between these measurements. This uses pre-formed post channels and plates of varying lengths, which give it a clean look for the high-security gate lock mounting platform. This can be assembled in minutes without special tools.

The post shim brackets are used to adjust the large and small post brackets to the pole or post. Sizes smaller than 2” or 3” respectively in 1/8” increments – ergo 1-7/8”, 1-3/4”, 1-5/8”, 2-7/8”, 2-3/4”, and 2-5/8” and etc. When two or more shims are used together on a single post, welding the bracket is highly recommended.

Each flex-mount kit includes all the necessary mounting hardware, including the four post shims.

This product comes pre-configured and included all the lock mounting hardware and post shims. It is 8" tall x 3/16" thick; its zinc-plated steel provides durability and long lasting life. The post brackets are also pre-drilled, the lock and strike brackets are pre-tapped. The lock and strike brackets are reversible, doubling the mounting variations. It allows superior adjustability of lock and strike before you finalize the welding. It also allows simple bolt-on installation or the entire system can be welded. Finally, it permits electronics to be mounted on either the fence post or gate post.

Models

These come in several different models, the FMB9-4 (Post Shim Kit for Flex Mount Brackets – Set of 4), the FMK-SL (Flex Mount Kit for Sliding Gate) and the FMK-SW (Flex Mount Kit for Swinging Gate).

MM15

Installation Instructions

Sell Sheet

Catalog Page

Patents: UL/cUL GWXT.R13976 /GWXT7.R13976

UL 10C Fire Rated, 1 hour

UL Certificate of Compliance (CoC)
CAN/ULC-S533 Listed

MM15 - Underwriter's Laboratories: File R21226

Patent Number: #6,902,214

Product Features

MM15 stands for MEMLOCK (Mechanical and Electromagnetic Lock). It has 4000lbs of holding force and provides an unmatched level of security, with dual voltage (12/24) and double current (AC/DC) operation for interior or perimeter doors where ultra-high security and smaller, compact sizes are required.

The MM15 is a hybrid design, which has two spring loaded, hardened steel jaws. This assists in the event of a forced entry attempt, where the mandibles will rotate inward, and clamp down; capturing the edges of the framework.

Its mounting plate provides an installation that is easy; its optional door position switch and anti-tamper switch help it to provide a safe security. It can be installed with battery backup power supply and option prep for use with ½” conduit. It has optional finishes via dress covers including black, polished brass and satin brass. It has brackets and accessories to configure any opening. This is for Indoor use only, and it comes with the MagnaCare lifetime replacement, no-fault warranty.

Specification Data

The Holding force is 4000lbs [1814 kg], and the operating temperature goes from -40 to +140F [-40 to +60C]. Its current draw and voltage come in two varieties. AC current: 130 mA max at 12 VAC, 250 mA max at 24 VAC, and DC current: 100 mA max at 12 VDC, 200 mA max at 24 VDC. The shipping weight is 6 lbs. It is UL Listed

Models

These come in four different models, the MM15 which is the standard (Electromechanical Maglock – 4000lbs), the MM15DT (Electromechanical Maglock – 4000lbs, DPS, Tamper), the MM15G (Electromechanical Maglock – 4000lbs, Conduit) and the MM15GDT (Electromechanical Maglock – 4000lbs, m Conduit, DPS, Tamper).

DC - MM15

Dress Covers

Catalog Page

The looks of the MM15 are dull, but they can be brightened up and given a cleaner finish with the DC-MM15 or dress covers. These dress covers are snap on. The brushed stainless dress cover is provided standard with the MM15. It comes in black, polished brass and satin brass. The dress covers must be purchased separately.

Models

DC-MM15BK (Black), the DC-MM15BP (Polished Brass) and lastly the DC-MM15BS (Satin Brass).

HEB - MM15

Header Extension Brackets Catalog Page

The HEB is the header extension brackets that are used with the MM15. To install the header bracket, fasten the bracket securely to structural supports using lag screws (not provided). Concrete anchors must be used if mounting it into masonry. It comes in multiple finishes both in black and clear, and different sizes.

Models

The 1” models are the HEB-1BK-MM15 (1”, Black Finish), the HEB-1CL-MM15 (1”, Clear Finish), the 2” models are the HEB-2BK-MM15 (2”, Black Finish), the HEB-2CL-MM15 (2” Clear Finish), and the 3” models are the HEB-3BK-MM15 (3” Black Finish), and the HEB-3CL-MM15 (3”, Clear Finish).

SFP - MM15

Stop Filler Plates

Catalog Page

The SFP helps with filling or extending a doorstop. It creates a flat mounting surface for the magnalock. This accessory comes in multiple finishes both in black and clear, and different sizes.

Models

The ½” models are the SFP-1/2BKMM15 (Black) and the SFP-1/2CLMM15 (Clear).

The 3/8” models are the SFP-3/8BKMM15 (Black) and the SFP-3/8CLMM15 (Clear).

The 5/8” models are the SFP-5/8BKMM15 (Black) and the SFP-5/8CLMM15 (Clear).

TS - MM15

Tamper Shield

Catalog Page

Installation Instructions

The tamper shield encases the lock face completely; this will provide an added layer of protection against attempts to compromise the magnetic locking mechanism. This prevents unwelcome access to MM15 strike plates using foreign objects or programs.

Models

There is only one model, the MM15-TS (Tamper Shield for MM15 – Stainless Steel)

Z – MM15

Z Bracket Kits

Catalog Page

Installation Instructions

This accessory comes only in one size, but two different colored models. This helps to accommodate openings and precise adjustments.

Models

There is the Z-MM15BK (Z-Bracket – MM15, Black) and the Z-MM15CL (Z-Bracket – MM15, Clear)

UNL

UnLatch Strike

Catalog Page

Installation Instructions

Architectural Specifications

Patents, Approvals, and Listings

  • UNL and MUNL - Windstorm Latching Hardware (ZHEM)
  • UL/cUL GXAY.R18923 / GXAY7.R18923
  • UL ZHEM.R25219
  • UL 10C Listed, 3-hour single door
  • UL listed to ANSI/ SDI-BHMA A250.13(60 PSI) Windstorm
  • UL Certificate of Compliance (CoC)
  • UNL and MUNL - Underwriter's Laboratories: File R18923
  • GXAY and GXAY7 Electric Strike for Fire Door (UL 10B & UL 10C)
  • CAN4-S104, CAN/ULC Listed
  • NFPA-252 fire door compliant
  • ANSI/BHMA A156.31, Grade 1; E09321,E09322, E09323
  • ASTM-E152 fire door compliant
  • Patent Numbers: #5,474,342, #6,022,056, #6,581,991

Product Features

UNL is a revolutionary new type of unlatch strike, which is used for any application where an electric strike would be used for a cylindrical/tubular lockset. Unlatch will support full dead latch functions which will release under pressure and include a latch status monitoring output. It eliminates the necessity to perform a routing operation on the door frame for installation. It also presents a concealed appearance, giving it an enhanced appeal to the installation. The security is also improved since an intruder is less able to determine the type of security device used on the door

FSUNL option: FSUNL allows the UNL and MUNL to become selectable for either “fail-safe” or “fail secure” operations.

This product fits standard ANSI 4-7/8" strike cutout; there is no cutting or altering of the jamb required. It's also available in polished brass (US03), and oil rubbed bronze (US10B). It's motorized, with no solenoids, it's entirely concealed installation, on continuous duty and maintains dead latch function at all times. It releases under pre-load, and the latch status sensor is standard (SPDT). It's UL listed and has MagnaCare lifetime replacement with no-fault warranty.

Specification Data

The holding force is 1500lbs [680 kg], and the operating temperature goes from -20 to +125F [-29 to +52C]. Its current draw and voltage come in two varieties 12VDC: 40mA continuous, minimum 300mA when operating, and 24VDC: 40mA continuous, minimum 200mA when operating. The shipping weight is 1.6lbs, and it is recommended for startup inrush to achiever best operation under pre-load.

Models

These come in four different models, the UNL-12 which is the standard (Unlatch for cylindrical locks - 12VDC), the UNL-12-10B (Unlatch - 12VDC, oil rubbed bronze), the UNL-24 (Unlatch for cylindrical locks - 24VDC) and the UNL-24-10B (Unlatch - 24VDC, oil rubbed bronze).

MUNL

Catalog Page Installation Instructions

Patents, Approvals, and Listings

  • UNL and MUNL - Underwriter's Laboratories: File R18923
  • UNL and MUNL - Windstorm Latching Hardware (ZHEM)
  • UL/cUL GXAY.R18923 /GXAY7.R18923
  • UL ZHEM.R25219
  • UL10C Listed
  • UL listed to ANSI/ SDI-BHMA A250.13(60 PSI) Windstorm
  • UL Certificate of Compliance (CoC)
  • CAN4-S104, CAN/ULC Listed
  • ANSI/BHMA A156.31, Grade 1; E09321,E09322, E09323
  • NFPA-252 fire door compliant
  • ASTM-E152 fire door compliant
  • GXAY and GXAY7 Electric Strike for Fire Door (UL 10B & UL 10C)
  • Patent Numbers: #5,474,342, #6,022,056, #6,581,991

Product Features

The MUNL is the mortises unlatch strike, which is used for any application where an electric strike would be used for a mortise type lock. most North American mortise locks (Sargent 7800 and 8200, which require tab kit model #STK-1 for retrofit installations).The mortise unlatch includes field adjustability for latch and dead latch positions, and it releases under pressure and includes a latch status monitoring output. Also rated by the American national s

Specification Data

The holding force is 1500lbs [680 kg], and the operating temperature goes from -20 to +125F [-29 to +52C]. Its current draw and voltage come in two varieties 12VDC: 40mA continuous, minimum 700mA when operating, and 24VDC: 40mA continuous, minimum 500mA when operating. It has a higher capacity supply (1-4 Amps) which is recommended for startup inrush to achiever best operation under pre-load. The shipping weight is 2lbs [0.91kg] it comes in 3 finishes, the US26D-626 – stainless steel, the US10B/613 – oil rubbed bronze, and the US03/605 – polished brass.

Models

Outside of the colors, there are two models, one that’s the MUNL-12 (12VDC) and the MUNL-24 (24VDC).

FSUNL

Fail Safe Unlatch Module

Catalog Page

Installation Instructions

The FSUNL is designed to work in conjunction with the UNL series or MUNL series. When interfaced with an unlatch device, the FSUNL will allow the user to choose between "fail-safe" or "fail secure" operations.

Models

There are two models with this product. The FSUNL-12 (Fail Safe/Fail Secure Unlatch Module, 12VDC, .90mA), and the FSUNL-24 (Fail Safe/Fail Secure Unlatch Module, 24VDC, 1.4mA).

Product Features

Unlatch strike, windstorm-rated, preload-handling electromechanical strike, MUNL mortise unlatch strike and the windstorm-rated, preload-handling strike for mortise locksets.